
Accounting Software for Manufacturers in Pakistan: An Industry Guide
In short: A factory has a harder accounting job than a shop. Stock changes shape, from raw material to work in progress to finished goods, and the real cost of each product depends on material, labour and overheads. This guide explains what Pakistani manufacturers, from food and packaging units to garment and plastic factories, should expect from accounting software and how to check it before buying.
Why factories outgrow ordinary accounting software
Most small business software was built for trading: buy an item, sell the same item. A manufacturer buys yarn, chemicals, granules or flour and sells something different. If the system cannot record that change, the owner ends up keeping production in a separate Excel sheet, and the accounts never show the true stock value or the true profit per product.
The common symptoms are familiar: the stock figure in the books is a guess at month-end, nobody knows the cost of the last batch, wastage is only noticed when material runs out, and the sales tax figures are prepared separately from the accounts.
The five areas a manufacturer needs covered
| Area | What the software should do | Why it matters |
|---|---|---|
| Raw material store | Record purchases, goods received, issues to production and returns, with units and conversions (bags, kg, rolls, metres) | Stops material from disappearing between the store and the floor |
| Bill of materials | Hold the standard recipe for each product or batch | Lets you issue the right material and see the expected cost |
| Production entries | Move stock from raw material to work in progress to finished goods, and record wastage and by-products | Gives a real stock value at every stage |
| Costing | Add labour and overheads to material cost to show the cost per unit or per batch | Shows which products actually make money |
| Sales and tax | Issue sales tax invoices from the same item master and keep data ready for FBR | One source of truth for accounts and tax |
How production costing works, in plain words
Suppose a unit makes a batch of 1,000 packets. The software adds up the material issued against the batch at its stock cost, adds the labour and an overhead share (electricity, gas, rent, machine maintenance), then divides by good units produced. Units rejected or wasted are not counted as good output, so wastage raises the cost per good unit, which is exactly what the owner needs to see.
Two settings matter here. First, the stock valuation method: most businesses use weighted average or FIFO, and the choice changes the material cost of each batch. Our guide to FIFO vs weighted average explains the difference. Second, the overhead basis: pick one fair basis, such as machine hours or units produced, and apply it consistently.
Keep it simple at first. A standard bill of materials plus actual material issues is enough for most small factories. Add detailed labour and overhead allocation only once the store and production entries are being done every day.
Sales tax points manufacturers cannot ignore
Most manufacturers supplying taxable goods are registered for sales tax. The standard rate on goods under section 3(1) of the Sales Tax Act, 1990 is 18 percent, although many items carry other rates or special treatment, so the rate must sit on each item rather than be typed on each invoice.
The monthly cycle is tight: sales data in Annex-C is due by the 10th of the following month, payment by the 15th and the return by the 18th. FBR digital invoicing is being made compulsory for sales-tax-registered businesses in phases, so every sales invoice should go to FBR in real time from the same system that keeps your accounts. Records must be kept for six years after the end of the tax period they relate to (section 24). See our sales tax invoice format guide for what each invoice must show.
Buyer checklist for manufacturers
- Units and conversions. Can it buy in bags and issue in kilograms, or buy in rolls and issue in metres, without manual maths?
- Bill of materials. Can you set a recipe per product and see expected vs actual material use for each batch?
- Stages of stock. Does it keep raw material, work in progress and finished goods separately, with wastage and by-products?
- Cost per unit. Can it show cost per batch and profit per product, not just total profit?
- Tax from the same data. Are sales tax invoices, HS codes and FBR digital invoicing handled from the same item list?
- Stock counts. Can you run a physical count and post differences with a reason? Our stock count guide explains the routine.
- Month-end. Can you close a month with stock, payables, receivables and bank reconciled in one place?
- Local support. Will someone help you set up items and recipes on site, in Urdu if needed?
A sensible rollout plan
Do not try to switch on everything in week one. Start with the chart of accounts, opening balances, item list and suppliers. Next, run purchases, sales and the raw material store daily for a few weeks. Only then switch on bills of materials and production entries, starting with your top products. Finally, compare system stock with a physical count and fix the differences before you rely on cost figures.
Switcher Techno’s accounting software covers accounts, inventory, sales tax invoicing and FBR digital invoicing in one system, with setup support from our Karachi team.
Running a factory on Excel and guesswork?
Message us on WhatsApp with what you make and how you track material today, and we will show you how production and costing would work in our software.
Frequently asked questions
Is normal shop accounting software enough for a factory?
Usually not. A factory must move stock from raw material to work in progress to finished goods and work out the cost of each batch. Shop software normally only tracks items bought and sold.
What is a bill of materials?
It is the recipe of a product: the raw materials, packing and quantities needed to make one unit or one batch. The software uses it to issue material and to estimate cost.
How should overheads like electricity and wages be added to product cost?
Choose one fair basis, such as machine hours, labour hours or units produced, and apply it the same way every month. Review the rate when your costs change sharply.
Do manufacturers in Pakistan need FBR digital invoicing?
Sales-tax-registered businesses are being brought onto FBR digital invoicing in phases, and manufacturers registered for sales tax should treat it as a requirement. Check your own status on the FBR website or with your tax adviser.
How long must a manufacturer keep sales tax records?
Under section 24 of the Sales Tax Act, 1990, records are kept for six years after the end of the tax period they relate to, or longer if proceedings are pending.
Can I start with accounts and add production later?
Yes. Many factories first move their accounts, purchases, sales and stock into the system, then switch on bills of materials and production entries once the item list is clean.
Tax rates and dates above were checked on 14 November 2026 and can change. Many items have special rates or treatment, so confirm your own position with the FBR or your tax adviser.
